Optical Communication Products · Shenzhen, China
Tel: +86 0755 23766314  ·  marketing@fotfiberoptic.com
Request a Quote
Measured fibre by fibreMPO/MTP Patch Jumper — FOT Fiber Optic
Configure the assembly below — fibre count, type, polish, polarity, gender, jacket and length all update the specification table live.

MPO/MTP Patch Jumper

SKU: FOT-MPO-JMP · Trunk & Jumper Cables

Short MPO-to-MPO interconnect for panel and transceiver patching.

12FFibre count
≤ 0.35 dBInsertion loss
2.0 mmSlim jacket
0.5–30 mLength range
Fibre count
12F8F16F24F
Fibre type
OM4 multimodeOM3 multimodeOM5 widebandOS2 single-mode (G.652.D)G.657.A1 bend-insensitive
Loss grade
Standard lossLow lossExtra low loss
Polish
UPC / PC (flat)APC (angled, 8°)
Gender
Female – Female (no pins)Male – FemaleMale – Male (pinned)
Jacket
LSZH 2.0 mmLSZH 3.0 mmOFNP plenum
Length
3 m0.5 m1 m2 m5 m10 m15 m30 m
Configured part numberFOT-MPO-JMP
Request a Quote Request Datasheet
Ships worldwide
Built to your configuration
3-year warranty

Product Overview

The short, flexible jumper that goes from a patch panel port to a transceiver, or between two adjacent panels. Same ferrule quality as the trunk but a thinner, more manageable jacket and lengths measured in metres rather than tens of metres.

Assemblies are built on US Conec MTP® ferrules and terminated in a controlled environment, then measured fibre by fibre. Interferometry checks the three geometry parameters that decide whether a multi-fibre ferrule mates properly — radius of curvature, apex offset and fibre height — and every end face is inspected and graded to IEC 61300-3-35 before the dust cap goes on.

Fibre count, fibre type, polish, polarity, gender, jacket rating, leg length and overall length are all build options rather than catalogue limits. Use the selector above to configure the exact assembly and the specification table will follow your choices; the measured test report ships with the cable.

Technical SpecificationsUpdates with your selection

Optical
Fiber Count12F
Fiber TypeOM4 50/125 µm laser-optimised multimode
Wavelength850 / 1300 nm
Insertion Loss≤ 0.35 dB
Return Loss≥ 30 dB multimode / ≥ 50 dB single-mode
Connector PolishUPC / PC — flat polish
PolarityType B (reversed)
Typical Insertion Loss0.25 dB
Loss GradeStandard
Mechanical & Environment
ConnectorUS Conec MTP® / MPO
GenderFemale to female — no guide pins
Cable JacketLSZH round, 2.0 mm
Jacket ColourAqua / Violet
Flame RatingIEC 60332-1 LSZH
Length3 m
Pull TabPush-pull tab fitted for high-density panels
Min. Bend Radius10 × cable OD dynamic, 5 × static
Crush Resistance≥ 1000 N / 100 mm
Tensile StrengthShort term 100 N / long term 30 N
Operating Temp-10 °C to +60 °C
Storage Temp-40 °C to +75 °C
ComplianceIEC 61754-7, TIA-604-5 (FOCIS-5/10), RoHS
Testing, Quality & Supply
Optical Test100% — every fibre measured for insertion loss and return loss before shipment
Ferrule GeometryInterferometer-verified: radius of curvature, apex offset and fibre height to IEC 61755-3
End-Face InspectionEvery ferrule inspected and graded to IEC 61300-3-35
Test ReportPer-fibre measured data supplied with the assembly, traceable to the serial number
Connector SourceUS Conec MTP® ferrules; genuine-brand or FOT MPO to your preference
CustomisationFibre count, type, polish, polarity, gender, jacket, leg length and overall length built to order
Lead TimeStock configurations 3–5 days; custom builds 7–10 days
Warranty3 years

Ordering Information

Part NumberConfigurationFibre countAvailability
FOT-MPO-JMPStandard configuration12FBuild to order
FOT-MPO-JMP-8FFibre count: 8F8FBuild to order
FOT-MPO-JMP-16FFibre count: 16F16FBuild to order
FOT-MPO-JMP-24FFibre count: 24F24FBuild to order
FOT-MPO-JMP-OM3Fibre type: OM3 multimode12FBuild to order
FOT-MPO-JMP-OM5Fibre type: OM5 wideband12FBuild to order
FOT-MPO-JMP-OS2Fibre type: OS2 single-mode (G.652.D)12FBuild to order
FOT-MPO-JMP-657A1Fibre type: G.657.A1 bend-insensitive12FBuild to order

Part numbers are indicative. Send us the fibre count, type, polish, polarity, gender, jacket and length and we confirm the exact build code on the quotation.

Quality & What's in the Box

Measured Fibre by Fibre

Insertion loss and return loss recorded for every fibre, not sampled.

Geometry Verified

Interferometer data on ferrule radius, apex offset and fibre height.

Inspected & Graded

Every end face checked against IEC 61300-3-35 before packing.

Packaging

Dust-capped, coiled on a reel or in a bag with the test report and pulling sock.

Typical Applications

Data Centre Spine & Leaf

Parallel 40G/100G/400G/800G backbone between spine, leaf and top-of-rack panels.

AI / GPU Clusters

Rail-optimised accelerator fabrics where one switch port breaks out to several GPUs.

Structured Cabling

Pre-terminated backbone that installs in hours instead of days, with the loss budget known up front.

Test & Commissioning

Loopbacks, attenuators and inspection for proving ports before the link goes live.

Frequently Asked Questions

Why is the jumper 2.0 mm when the trunk is 3.0 mm?

Bend radius and panel density. A 2.0 mm jacket dresses into a crowded 1U panel without violating its bend radius, where a 3.0 mm cable would fight you. The trade-off is lower crush resistance, which is fine for a jumper that lives inside a cabinet and irrelevant for a trunk in a tray.

Do I need a pull tab?

In a full 1U panel, yes. Without one you end up gripping the cable to unseat the connector, which is how ferrules get contaminated and latches get broken. It costs nothing to specify and it is fitted as standard.

How is the assembly labelled?

Both ends carry a printed label with the part number, fibre count, fibre type, polarity type and the serial number, and breakout legs are individually numbered. Tell us your own labelling convention on the RFQ and we print to it — it costs nothing and it saves an afternoon at installation.

Can I get free samples before ordering volume?

Yes. We supply qualification samples so you can measure the loss and check the fit in your own panels before committing. Per-order test reports are standard, and sample reports can be provided in advance for tender documentation.

Related MPO / MTP Products

MPO/MTP Trunk Cable
Trunk & Jumper Cables

MPO/MTP Trunk Cable

MPO/MTP Bundle / Multi-Leg Trunk Cable
Trunk & Jumper Cables

MPO/MTP Bundle / Multi-Leg Trunk Cable

MPO/MTP to LC / SC / FC Harness Cable
Harness, Hydra & Conversion

MPO/MTP to LC / SC / FC Harness Cable

MPO/MTP to LC Hydra Breakout Cable
Harness, Hydra & Conversion

MPO/MTP to LC Hydra Breakout Cable

Request a quote for this part

Tell us the platform and the quantity. An engineer checks the part against your switch and software version before quoting — if it will not work, we say so.

Goes to our engineers and the quotation desk together. Replies come from sales@topnetsystem.com, usually within one working day.